1.Pastikan target device telah mengirim syslog message ke Collector Manager Server.

- Cek Setting syslog, pastikan target device mengirimkan syslog ke IP Coll Manager Server benar
- Untuk memastikan device telah mengirim syslog message, kita dapat menggunakan tools syslog receiver seperti kiwisyslog.

2.Jika target device telah mengirimkan syslog message, lakukan pengecekan pada Collector Manager Server.
- Login ke Collector Manager dimana device melempar lognya, (Anda dapat menggunakan telnet/ssh client spt PuttY atau xManager)

- Login sebagai user esecadm, kemudian masuk ke directory Sentinel, ketikkan command :
$ cd $WORKBENCH_HOME

- Pastikan syslog server running
$ cd syslog
$ ./syslog-server.sh status

3.Lakukan pengecekan pada syslog-server apakah syslog message sudah diterima.

Command dieksekusi di collector manager dengan IP = 10.1.99.99, mengecek apakah syslog dari IP 10.1.10.17 sudah masuk ke syslog server

$ java -jar syslog/lib/syslogconnector.jar -proxy 10.1.99.99:9091 -id Squid1 -sender 10.1.10.17

-proxy 10.1.9.99:9091 (IP collector manager)

-id Squid1 (Id harus uniq, jika ada dua eksekusi dengan id sama syslog akan error)

-sender 10.1.10.17 (target device yg mengirimkan syslog message)

Setelah command tersebut dieksekusi, Jika server menerima sysloge message maka akan tampil syslog message di layar console

Anda dapat mengcopy command tsb di Rx/Tx Value pada collector builder.

4.Jika syslog belum juga muncul, coba restart syslog server.

Untuk merestart syslog server anda harus login sebagai user root

Ketik “su –“ untuk login sebagai root, Masukkan password
Ketik “cd $WORKBENCH_HOME\syslog”
Ketik “./syslog-server.sh stop”
Ketik “./syslog-server.sh start”

Untuk melakukan pengetesan syslog server pada collector manager apakah sudah berjalan dengan baik, dapat menggunakan Kiwi Syslog Gen untuk men-generate syslog message dan dikirim ke server

5. Lakukan langkah 3 , setelah anda memastikan bahwa syslog server bekerja dengan baik.

Jika syslog belum diterima, coba cek kembali setting target device

install solaris to your computer, download for free solaris sparc here

here is configuration that u need to set Automatic IP address on solaris 10, so u dont need manually run “ifconfig command” every time after rebooting your system.

just for additional information here is my box detail

bash-3.00# uname -a
SunOS HhANSUN 5.10 Generic_120012-14 i86pc i386 i86pc

oke… lets get it on. for first step we will look our interface with ifconfig command, its just for make sure that we have eth in our system.

> ifconfig

bash-3.00# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
pcn0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.16.30.15 netmask ffff0000 broadcast 172.16.255.255
ether 0:c:29:64:f3:4
as we see, we have two interface lo0 for loopback and pcn0.

run this command to set IP address. bash-3.00# ifconfig pcn0 172.16.30.15 netmask 255.255.255.0 u must execute that command every time after restarting your system.  we need to edit some configuration file to make our system set IP address automatic at start.

> edit /etc/netmask

bash-3.00# more /etc/netmasks
#
# The netmasks file associates Internet Protocol (IP) address
# masks with IP network numbers.
#
# network-number netmask
#
# The term network-number refers to a number obtained from the Internet Network
# Information Center.
#
# Both the network-number and the netmasks are specified in
# “decimal dot” notation, e.g:
#
# 128.32.0.0 255.255.255.0
#
172.16.30.0 255.255.255.0

> edit /etc/hosts

bash-3.00# more /etc/hosts
#
# Internet host table
#
::1 localhost
127.0.0.1 localhost
172.16.30.15 HhANSUN loghost

> /etc/inet/ipnodes

bash-3.00# more /etc/inet/ipnodes
#
# Internet host table
#
::1 localhost
127.0.0.1 localhost
172.16.30.15 HhANSUN loghost

> /etc/defaultrouter (optionael)

Adopted from : http://hhan.wordpress.com